Battery tester analyzer plus#
Battery tester analyzer free#

Step 4: Cranking Test: After selecting the cranking test function, follow the prompts to start the engine.

Step 3: Battery Test: First, select the type of battery to be tested, then the test criteria and the test range, and then you have the results within a few seconds.

Step 2: Connect the 12V battery, red clips to the positive pole, and black clips to the negative pole.

Step 1: When doing a battery test, please make sure the car is off.

The working principle of the AUTOOL battery tester is to measure the ions on the surface of the plates to determine their chemical reaction ability and to infer the change of battery capacity by the change of the plates it can compare the actual conductivity value measured by the battery with the standard conductivity value when the battery is in good condition, so as to determine the health condition of the battery.ĪUTOOL BT360 12V Car Battery Load Tester Features : It provides techs or DTYers with a quick, simple, and cost-effective solution to know the battery’s charging status better, check the battery’s health, and detect faults.

Simulated 20 hour (C20) load test to 10.AUTOOL BT360 Digital Automotive Diagnostic Battery Tester Analyzer Charging Scanner ToolĪUTOOL BT360 Car Battery Load Tester is dedicatedly developed to test 12V regular flooded, automotive lead-acid batteries, AGM flat plate, AGM spiral, GEL, and EFB batteries. Max 30VDC (10 sec.) with Red LED IndicationĦV (1.2Ah to 10Ah) and 12V (1.2Ah to 100Ah)

Battery tester analyzer plus#

When performing accurate comparison tests between the ACT 612 and previous ACT GOLD PLUS models, carefully unplug leads from one tester to the other and do not disturb test lead connection to the batteryĬlick here for further Battery Testing Tips.

Quick Tip – Test comparisons between the ACT 612 and ACT GOLD PLUS Intelligent Battery Testers

Supplied: ACT 612 Intelligent Battery Tester, ACT 612TL Test Leads, ACT 430N Soft Carry Case, Sample ACT BTL Labels, Operating Instructions and Certificate of Calibration. This method is significantly more accurate than measuring voltage and internal resistance and does not deplete the battery unlike a conventional battery load tester. The ACT 612 uses advanced pulse load technology to analyze Ah capacity, based on the battery’s temperature and state of charge. This feature enables the unit to be calibrated to test various lead acid battery technologies or to specific brands of batteries. A quick look up table shows common battery sizes and at what Ah capacity rate they should be recharged or replaced. By giving a clear and accurate reading of a battery’s Ah capacity available, the ACT 612 makes it easy to identify replacements quickly. Results indicate when to recharge or replaceīattery manufacturers recommend to recharge or replace a battery when its rated Ah capacity falls below 65%. Once connected – ensuring a tight connection to clean battery terminals – the ACT 612 automatically displays the DC Voltage available followed by the Ah capacity reading. The ACT 612 will test 6V battery models between 1.2Ah and 10Ah, and 12V battery models between 1.2Ah and 100Ah. Use the Calibration Control to select either standby SLA, cyclic GEL and car FLOODED battery types prior to testing. Used by engineers from various industries from security, telecommunications to mobilityĭual voltage, designed for common lead acid battery types.

Battery tester analyzer free#

Simple in operation, free from complicated settings and no user interpretation of results is required.Powered by the battery under test, with ultra low heat generation for continuous testing.Displays DC Voltage and the actual Ampere hour (Ah) capacity available.Tests 6V batteries between 1.2Ah and 10Ah, and 12V batteries between 1.2Ah and 100Ah.

Developed for standby SLA, cyclic GEL and car FLOODED batteries.

No ordinary battery load tester, the ACT 612 simulates a 20 hour (C20) discharge test in seconds.

New compact and robust design with enhanced accuracy and result delivery time.